RAY FLASH Adapter unik ini dikembangkan oleh seorang fotografer profesional dari Republik Ceko. Alat ini dirancang seringan dan seportabel mungkin. Tidak ada alat elektronik, tidak ada flashtubes dan tidak ada kabel! Alat ini menggunakan sistem cerdas menyalurkan cahaya melalui akrilik dan reflektor untuk mendistribusikan cahaya yang dipancarkan dari lampu kilat secara merata di sekitar diameter besar adaptor ringflash. Hal ini menciptakan efek pencahayaan yang sama biasanya hanya tersedia dari unit ringflash yang dibuat oleh produsen peralatan studio flash, yang mahal, berat dan menyulitkan gerakan fotografer (karena memiliki kabel tersambung ke ringflash untuk daya).
RAY FLASH Adapter menciptakan efek pencahayaan yang sangat khusus : efek bayangan 3D. Karena cahaya semua berasal dari depan, yaitu dari sekitar lensa, menghasilkan sebuah bayangan - hampir tidak terlihat pada bagian depan subjek Anda, sementara bayangan bahkan lembut muncul di sekitar tepi. Ini cocok untuk fashion, potret, kecantikan, pernikahan & fotografi makro sebagai cahaya utama atau fill-in. RAY FLASH Adapter tidak mengubah temperatur warna flash dimana kekuatan dan berat tambahan dengan mudah dapat diakomodasi oleh lampu kilat pada kamera
Awards- PHOTO FORUM 2008 in Moscow- Editor´s Choice 2008: Lighting in USA- Winner: 2009 Professional Photographer Magazine Hot One Award
How to fit the Ringflash Adapter:
The Ringflash Adapter is mounted to the front of a portable flash unit, for example Canon 580 or Nikon SB800, and it is small and light weight enough to allow complete mobility!
Line up the flash unit with the rear receptacle of The Ringflash Adapter
Push the flash unit in as far as it will go
Turn the pressure plate at the top of The Ringflash Adapter clockwise to lock
The RAY FLASH Adapter is a very affordable way to achieve typical ringflash lighting quality normally only available to studio flash equipment users!
The unique RAY FLASH Adapter was developed by a professional photographer from the Czech Republic. It was designed to be as light and as portable as possible. There are no electronics, no flashtubes and no cumbersome cables! It uses a clever system of acrylic light channels and reflectors to distribute the light emitted from the flash unit evenly around the large diameter of the ringflash adapter. This creates the same lighting effect normally only available from ringflash units made by studio flash equipment manufacturers, which are expensive, heavy and tethered (they have a cable from ringflash to power pack).
The RAY FLASH Adapter creates a very special lighting effect: a "3-d shadow-wrapped look". Because all light originates from the front, i.e. from around the lens, it produces a virtually shadow-less look on the front of your subject, while a soft even shadow appears around the edges. It is ideally suited for fashion, portrait, beauty, wedding & macro photography as a main or fill-in light.
The RAY FLASH Adapter does not change the colour temperature of the flash that powers it and the additional weight can easily be accommodated by the on-camera flash unit.
The RAY FLASH Adapter is made to fit the Canon 580EX , Canon 580EXII and Nikon SB-800 ,Nikon SB-900 flash units and due to the its large inner diameter the ringflash adapter will accept almost all lenses from Nikon & Canon. For model range see chart below.
Model Range:
RAN These models fit the Nikon SB-800 and Nikon SB-900
RAC This model is for Canon 580EX and 580EX II
Nikon SB-800 with Nikon Body
| Code |
|
Available
|
|
RAN160
|
Nikon SB-800 &
D1,D700,D300,D300s,D200,D100,D90,D80,D70,D5000
|
From Stock
|
|
RAN170
|
Nikon SB-800 & D2,D2x,D3,D3x
|
From Stock
|
Nikon SB-900 with Nikon Body
|
Code
|
|
Available
|
|
RAN179
|
Nikon SB-900 &
D1,D700,D300,D300s,D200,D100,D90,D80,D70,D5000
|
From Stock
|
|
RAN189
|
Nikon SB-900 & D2,D3,D3x
|
From Stock
|
Canon Speedlite 580EX with Canon Body
|
RAC160
|
Canon580EX &
1100D,350D,400D,450D,500D,550D,600D
|
From Stock
|
|
RAC170
|
Canon 580EX &
10D,20D,30D,40D,50D,60D,5D,5D MKII,7D
|
From Stock
|
|
RAC175
|
Canon 580EX &1D,1Ds,1V
|
From Stock
|
Canon Speedlite 580EX II with Canon Body
|
RAC160-2
|
Canon 580EX &
1100D,350D,400D,450D,500D,550D,600D
|
From Stock
|
|
RAC170-2
|
Canon 580EX &
10D,20D,30D,40D,50D,60D,5D,5D MKII,7D
|
From Stock
|
|
RAC175-2
|
Canon 580EX II &1D,1Ds,1V
|
From Stock
|
Exposure control: when using Canon or Nikon cameras (or their derivatives) all TTL functions are operational as usual, as well as manual mode. In MANUAL control of the exposure is by use of a light meter or through test-shots on a digital camera.
Light output: The Ringflash Adapter is very efficient and the loss of light is surprisingly low! There is a difference in light efficiency between the SIRC and the RAN/RAC models, the latter being more efficient.
POWER OUTPUT GUIDE for RAC & RAN models
|
ISO
|
Flash Power
|
Distance
|
f/stop
Canon 580EX II
|
f/stop
Nikon SB800
|
|
100
|
1/1
|
0.6m/2ft
|
22.6
|
16.5
|
|
100
|
1/1
|
1.2m/4ft
|
11.1
|
11.2
|
|
100
|
1/1
|
1.8m/6ft
|
8.0
|
7.5
|
|
100
|
1/1
|
2.4m/8ft
|
7.2
|
4.9
|
|
100
|
1/1
|
3.1m/10ft
|
4.5
|
4.2
|
How to fit the Ringflash Adapter:
The Ringflash Adapter is mounted to the front of a portable flash unit, for example Canon 580 or Nikon SB800, and it is small and light weight enough to allow complete mobility!
|
|
|
|
|
|
| Line up the flash unit with the rear receptacle of The Ringflash Adapter |
|
Push the flash unit in as far as it will go |
|
Turn the pressure plate at the top of The Ringflash Adapter clockwise to lock |
Technical Specification
| Code |
Outer Diameter
|
Inner Diameter
|
Centre of ringflash to centre flash unit
|
Weight
Gram
|
|
RAN160
|
175
|
103
|
160
|
462
|
|
RAN170
|
175
|
103
|
170
|
478
|
|
RAN179
|
175
|
103
|
170
|
|
|
RAN189
|
175
|
103
|
180
|
|
|
RAC160
|
175
|
103
|
160
|
462
|
|
RAC170
|
175
|
103
|
170
|
478
|
|
RAC175
|
175
|
103
|
175
|
495
|
|
RAC160-2
|
175
|
103
|
160
|
462
|
|
RAC170-2
|
175
|
103
|
170
|
478
|
|
RAC175-2
|
175
|
103
|
175
|
495
|
All measurements in millimetre & gram
Guide to the model range and suitability of different camera models:
Canon & Nikon each make a large range of camera models and they have different body heights, which affects the difference between the centre of the bayonet mount (optical axis for the lens) and the hot-shoe. We list the camera models with the RA that gives the best position for the lens, i.e. lens is in the centre of the RA or as near as possible to the centre. But actually you can use almost all camera/lens combination with most of the model range! In fact people often buy a different RA model to that recommended, because the model they want is not available yet and they don't want to wait OR a photographer might have several different bodies or he/she may be planning to buy a different body soon. For instance the D1/D2 can be used with the RAN160 and the 170 (the lens would be more central with the 170). The fact that the lens is not central is only a cosmetical issue, but technically makes no difference to the light output or quality. The new D3 is the highest body that Nikon have made so far and that can realistically only be used with the RAN170 to accommodate almost all lenses. BUT we have used the D3 with a few lenses that are relatively small in diameter and that works fine, however the "fatter" zoom lenses would not fit physically into the RAN160.
To illustrate this we have checked a few Nikon bodies with a RAN160:
D300 lens is central, good for all lenses
D80 lens is slightly upwards of centre, good for all lenses
D60 lens is slightly upwards of centre, good for all lenses
D3 lens is below centre, but all prime lenses will be ok, and some zoom lenses, but the "fatter" zoom lenses will not fit into the ringflash adapter. The D3 should ideally be used with the RAN170!
At the moment there are no plans to introduce a RAY FLASH Adapter for other types & makes of flash units.
Radiation diagram
Measurements
The RAY FLASH Adapter is a very affordable way to achieve typical ringflash lighting quality normally only available to studio flash equipment users!
The unique RAY FLASH Adapter was developed by a professional photographer from the Czech Republic. It was designed to be as light and as portable as possible. There are no electronics, no flashtubes and no cumbersome cables! It uses a clever system of acrylic light channels and reflectors to distribute the light emitted from the flash unit evenly around the large diameter of the ringflash adapter. This creates the same lighting effect normally only available from ringflash units made by studio flash equipment manufacturers, which are expensive, heavy and tethered (they have a cable from ringflash to power pack).
The RAY FLASH Adapter creates a very special lighting effect: a "3-d shadow-wrapped look". Because all light originates from the front, i.e. from around the lens, it produces a virtually shadow-less look on the front of your subject, while a soft even shadow appears around the edges. It is ideally suited for fashion, portrait, beauty, wedding & macro photography as a main or fill-in light.
The RAY FLASH Adapter does not change the colour temperature of the flash that powers it and the additional weight can easily be accommodated by the on-camera flash unit.
The RAY FLASH Adapter is made to fit the Canon 580EX , Canon 580EXII and Nikon SB-800 ,Nikon SB-900 flash units and due to the its large inner diameter the ringflash adapter will accept almost all lenses from Nikon & Canon. For model range see chart below.
Model Range:
RAN These models fit the Nikon SB-800 and Nikon SB-900
RAC This model is for Canon 580EX and 580EX II
Nikon SB-800 with Nikon Body
| Code |
|
Available
|
|
RAN160
|
Nikon SB-800 &
D1,D700,D300,D300s,D200,D100,D90,D80,D70,D5000
|
From Stock
|
|
RAN170
|
Nikon SB-800 & D2,D2x,D3,D3x
|
From Stock
|
Nikon SB-900 with Nikon Body
|
Code
|
|
Available
|
|
RAN179
|
Nikon SB-900 &
D1,D700,D300,D300s,D200,D100,D90,D80,D70,D5000
|
From Stock
|
|
RAN189
|
Nikon SB-900 & D2,D3,D3x
|
From Stock
|
Canon Speedlite 580EX with Canon Body
|
RAC160
|
Canon580EX &
1100D,350D,400D,450D,500D,550D,600D
|
From Stock
|
|
RAC170
|
Canon 580EX &
10D,20D,30D,40D,50D,60D,5D,5D MKII,7D
|
From Stock
|
|
RAC175
|
Canon 580EX &1D,1Ds,1V
|
From Stock
|
Canon Speedlite 580EX II with Canon Body
|
RAC160-2
|
Canon 580EX &
1100D,350D,400D,450D,500D,550D,600D
|
From Stock
|
|
RAC170-2
|
Canon 580EX &
10D,20D,30D,40D,50D,60D,5D,5D MKII,7D
|
From Stock
|
|
RAC175-2
|
Canon 580EX II &1D,1Ds,1V
|
From Stock
|
Exposure control: when using Canon or Nikon cameras (or their derivatives) all TTL functions are operational as usual, as well as manual mode. In MANUAL control of the exposure is by use of a light meter or through test-shots on a digital camera.
Light output: The Ringflash Adapter is very efficient and the loss of light is surprisingly low! There is a difference in light efficiency between the SIRC and the RAN/RAC models, the latter being more efficient.
POWER OUTPUT GUIDE for RAC & RAN models
|
ISO
|
Flash Power
|
Distance
|
f/stop
Canon 580EX II
|
f/stop
Nikon SB800
|
|
100
|
1/1
|
0.6m/2ft
|
22.6
|
16.5
|
|
100
|
1/1
|
1.2m/4ft
|
11.1
|
11.2
|
|
100
|
1/1
|
1.8m/6ft
|
8.0
|
7.5
|
|
100
|
1/1
|
2.4m/8ft
|
7.2
|
4.9
|
|
100
|
1/1
|
3.1m/10ft
|
4.5
|
4.2
|
How to fit the Ringflash Adapter:
The Ringflash Adapter is mounted to the front of a portable flash unit, for example Canon 580 or Nikon SB800, and it is small and light weight enough to allow complete mobility!
|
|
|
|
|
|
| Line up the flash unit with the rear receptacle of The Ringflash Adapter |
|
Push the flash unit in as far as it will go |
|
Turn the pressure plate at the top of The Ringflash Adapter clockwise to lock |
Technical Specification
| Code |
Outer Diameter
|
Inner Diameter
|
Centre of ringflash to centre flash unit
|
Weight
Gram
|
|
RAN160
|
175
|
103
|
160
|
462
|
|
RAN170
|
175
|
103
|
170
|
478
|
|
RAN179
|
175
|
103
|
170
|
|
|
RAN189
|
175
|
103
|
180
|
|
|
RAC160
|
175
|
103
|
160
|
462
|
|
RAC170
|
175
|
103
|
170
|
478
|
|
RAC175
|
175
|
103
|
175
|
495
|
|
RAC160-2
|
175
|
103
|
160
|
462
|
|
RAC170-2
|
175
|
103
|
170
|
478
|
|
RAC175-2
|
175
|
103
|
175
|
495
|
All measurements in millimetre & gram
Guide to the model range and suitability of different camera models:
Canon & Nikon each make a large range of camera models and they have different body heights, which affects the difference between the centre of the bayonet mount (optical axis for the lens) and the hot-shoe. We list the camera models with the RA that gives the best position for the lens, i.e. lens is in the centre of the RA or as near as possible to the centre. But actually you can use almost all camera/lens combination with most of the model range! In fact people often buy a different RA model to that recommended, because the model they want is not available yet and they don't want to wait OR a photographer might have several different bodies or he/she may be planning to buy a different body soon. For instance the D1/D2 can be used with the RAN160 and the 170 (the lens would be more central with the 170). The fact that the lens is not central is only a cosmetical issue, but technically makes no difference to the light output or quality. The new D3 is the highest body that Nikon have made so far and that can realistically only be used with the RAN170 to accommodate almost all lenses. BUT we have used the D3 with a few lenses that are relatively small in diameter and that works fine, however the "fatter" zoom lenses would not fit physically into the RAN160.
To illustrate this we have checked a few Nikon bodies with a RAN160:
D300 lens is central, good for all lenses
D80 lens is slightly upwards of centre, good for all lenses
D60 lens is slightly upwards of centre, good for all lenses
D3 lens is below centre, but all prime lenses will be ok, and some zoom lenses, but the "fatter" zoom lenses will not fit into the ringflash adapter. The D3 should ideally be used with the RAN170!
At the moment there are no plans to introduce a RAY FLASH Adapter for other types & makes of flash units.
Radiation diagram
Measurements
BACK
OTHERS
